Save on Pinterest

How to Make a DIY Face Mask

Keep yourself and others safe and healthy by wearing this DIY face mask.

1 / 10
Rike/Getty Images

The most current CDC guidelines recommend the use of cloth face masks in public settings where other social distancing measures are difficult to maintain (e.g., grocery stores and pharmacies). Recent studies have shown most face masks offer a level of protection and may help curb the spread of COVID-19, even if they are not the approved N-95 mask. With many folks heeding the Surgeon General’s warning and leaving N-95 masks for frontline health workers, DIY face masks are the way forward for many of us.

So, here’s our guide to a DIY face mask using common items in your home. This project was completed at my kitchen table one night after dinner.

2 / 10
via Family Handyman

Materials you’ll need:

  • For the mask:
    • Two pieces of fabric about a 9-1/2 in. square each.
  • For the strap:
    • Cloth
    • Ribbon
    • String
    • Shoelaces
    • Stretch-band material or rubber bands
    • Sewing thread

Tools you’ll need:

  • Yardstick
  • Tape measure
  • Scissors and/or utility knife
  • Iron
  • Sewing machine or needle and thread

Here’s how to clean and disinfect your home, according to the CDC.

3 / 10
via Family Handyman

1. Choose and Cut Fabric

A Cambridge University study shows that antimicrobial pillowcases, cotton-blend t-shirts and dish towels filter a higher percentage of particles, but any lightweight, washable fabric will give some level of protection. The thinner your fabric, the easier your sewing.

It’s best to choose different types of fabric so you can tell inside from out when putting on the mask. We found some leftover material from a previous project and some plain white muslin. Lay your two fabrics over each other and cut out a 9-1/2 in. square.

4 / 10
via Family Handyman

2. Edge Stitch #1

With your two square pieces of cloth layered over each other, fold over two parallel edges about 3/8 in. and iron them flat. Many plans we looked at called for hand pinning folds and pleats for edge stitching, but if you’re not a seasoned seamstress you’ll find ironing far easier.

Once your edges are folded over, stitch those same two edges. On our mask-making night, my partner assembled a half-a-dozen masks on a sewing machine in the time it took me to stitch one by hand. While I’m much better with a hammer or power tool in hand, I found the quiet task of hand stitching relaxing, even if my results paled in comparison to those from the sewing machine. These all-day baking projects will also help you relax while you’re stuck at home. 

5 / 10
via Family Handyman

3. Create Pleats

A pleated mask will provide the best universal fit. Keeping the stitched edges top and bottom, iron in three pleats, leaving a total width of about three inches.

6 / 10
via Family Handyman

4. Edge Stitch #2

Keeping the pleats in place, stitch the short edges. Have bored kids at home? Check out 100 fun things you can do with your kiddos.

7 / 10
via Family Handyman

5. Choose Straps and Cut to Length

Strap design can vary depending on what you have on hand. It can be any ribbon, string, shoestring, stretch-band or fabric less than 3/8 in. wide. The two predominant strap styles are tie straps or ear loops.

Tie straps should be cut to about 18 in. long. If you do have stretch band material, best to cut the ear loops at eight inches long. If you decide to use fabric, cut an 18 x 3/4 in. wide strip, fold and iron the edges to its middle, then do a zig-zag stitch up the center.

8 / 10
via Family Handyman

6. Attach Straps

If you’re making ear loop straps, attach them perpendicular to the mask at the corners. With string or any strap material less than a one-quarter inch, best to make a small loop or knot when you stitch it to the face mask.

Tie straps should be attached at a 45-degree angle in the corners of the mask. If you make tie straps, you can tie loops in them and integrate rubber bands. This tip makes for a snug fit on the face and gets around the awkward task of having to tie on the mask on behind your head.

9 / 10
via Family Handyman

Wearing a Mask

For full effectiveness make sure your mask fits snugly. Despite the inconvenience of tie straps, I find them best for getting a good seal on my face. Avoid touching the mask while using it and sanitize your hands after handling it.

Be sure to wash your mask regularly to keep it germ-free. It’s not a bad idea to have two or three for yourself and keep them in rotation in your laundry. It’s best to wash in hot water with regular detergent, and dry on a high heat setting. By the way, here’s how to effectively disinfect your sheets.

Always sanitize your hands after handling and do not touch your face. This is also a good rule of thumb if you’re planning on gifting or donating your masks. The Sewing and Craft Alliance has an updated list of health care facilities nationally that have asked for fabric mask donations.

10 / 10
sv_sunny/Getty Images

Stay Safe and Healthy

Much of what we know about this coronavirus is changing day to day, yet one fact has remained constant: It is primarily transmitted through the nose and mouth. So it makes sense that wearing a mask may slow the spread of the virus. Next, read up on our favorite stay-at-home recipes.

The Family Handyman
Originally Published on The Family Handyman
Subscribe & SAVE Save Up To 80%!